Trimble SPS881 GNSS Smart Antenna Installed Options SPS881 P/N: 59355-64 430-450MHz Radio Module P/N: 62481-64
|
CMR Inputs CMR Outputs RTCM Inputs RTCM Outputs Data Collector Bluetooth L2CS UHF Transmit Enable GLONASS Enable Webserver Login Required 430-450MHz Radio Module P/N: 62481-64
|
Trimble SPS881 Smart GPS Antenna The Trimble® SPS881 Smart GPS Antenna provides a rugged and highly portable GPS base station and rover solution for grade checkers and site engineers on site development or highways projects that require precise site measurement and stakeout capability.
The SPS881 Smart GPS Antenna can operate in Location GPS modes with Satellite Based Augmentation Systems (SBAS), as a rover in Real–Time Kinematic (RTK) mode with corrections from a site base station, Internet base station or VRS™ network and can act as a site base station for RTK operations.
In combination with the Trimble SCS900 Site Controller Software, the receivers provide the capability to:
- Determine cut fill anywhere on the jobsite
- Stake out site or road features, utilities, daylight lines and side slopes
- Carry out site measurements for progress and material stockpile volume computations
- Carry out as–built measurements, grade checks and laid material thickness checks
Easy Setup Saves Time and Money The Trimble SPS881 model is easier than ever to set up.
The SPS881 Smart GPS Antenna make setup for base station and rover operation quick, easy and hassle–free
Base Station Operation:
- One component to set up
- One button to start up using AutoBase technology
- Bluetooth cable–free operation when using a controller
- Easy to understand status LEDs that show receiver is switched on, tracking satellites and transmitting corrections
Rover Operation:
- One component to set up
- One button to start up
- Bluetooth cable–free operation
- Automatically connect using the last used rover settings and source of corrections
- Easy to understand status LEDs that show receiver is switched on, tracking satellites and receiving corrections
Rover set up is fast and easy–just switch on the receiver, start up the controller and you’re ready to go. And, because the GPS receiver, GPS antenna, radio, radio antenna and battery are integrated into one housing, you don’t have to deal with cables and multiple components. It saves time and money by making them simple to transport and fast to setup.
Trimble AutoBase functionality provides users with rapid repeat daily set up of the base station without the need for a controller.
Integrated radio The SPS881 Smart GPS Antenna has a integrated license–free 900 MHz spread spectrum or 450 MHz UHF radios for receiving or transmitting base station corrections. The Smart GPS antenna can be used with cellular communications for connection to VRS networks, Internet–enabled base stations for long–range operation and to provide infill for areas where base station corrections are unavailable over radio.
A future–proof investment Available in a range of options to suit your application and performance requirements, versatile Trimble GPS receiver is a future-proof investment.
The SPS881 Smart GPS Antenna is designed to receive current and future satellite signals. This receiver supports GPS modernization through support of L2C code and can be upgraded to receive GLONASS or L5 GPS signals, protecting your investment well into the future.
Improved GPS Performance The new Trimble RTK engine improves performance under tree canopy and reduces initialization time after loss of lock, delivering high performance in a variety of measurement conditions.
Features:
- Integrated GPS receiver, GPS antenna, radio and battery in a small lightweight and robust housing
- Cable–free base or rover operation using Bluetooth® technology
- Rapid daily base station setup with a single button push using AutoBase™ technology
- High mobility base or rover GPS receiver for site measurement and stakeout applications
- Integrated license–free 900 MHz radio or 450 MHz UHF radio
- Supports base station–free VRS messages or an Internet–enabled base station through GSM/GPRS phone with controller or modem in controller
- Supports GPS and L2C modernized GPS signals
Specifications:
Dimensions (W × H)
|
19 cm (7.5 in) × 11.2 cm (4.4 in) including connectors
|
Measurements
|
72-channel L1 C/A code, L1/L2 GPS Full Cycle Carrier, L2C Full Cycle Carrier
|
Base and Rover Interchangeability
|
Yes
|
Rover position update rate |
1 Hz, 2Hz, 5 Hz, 10 Hz, 20 Hz
|
Rover maximum range from base
|
Unrestricted Typical range 3 – 5km (1.8 – 3 miles) without radio repeater
|
Rover operation within a VRS network
|
Yes
|
Code differential GPS positioning *2*
|
Horizontal accuracy |
0.25 m + 1 ppm RMS (0.8 ft + 1 ppm RMS)
|
Vertical accuracy
|
0.5 m + 1 ppm RMS (1.6 ft + 1 ppm RMS)
|
SBAS (WAAS/EGNOS/MSAS) positioning *3* |
Horizontal accuracy
|
Typically <1 m (3.3 ft)
|
Vertical accuracy |
Typically <5 m (16.4 ft)
|
Real-Time Kinematic (RTK) Positioning
|
Horizontal accuracy
|
10 mm + 1 ppm RMS (0.032 ft +1 ppm RMS)
|
Vertical accuracy
|
20 mm + 1 ppm RMS (0.065 ft +1 ppm RMS)
|
Initialization Time
|
Regular RTK operation with base station
|
Single/Multi-base minimum 10 seconds + 0.5 times baseline length in km, up to 30 km
|
RTK operation with Scalable GPS infrastructure
|
Typically <30 seconds anywhere within coverage area (Max and Extreme options only)
|
Initialization reliability *4*
|
>99.9%
|
Power
|
Internal
|
Rechargeable, removable 7.4 V, 2.4 Ah Lithium-ion battery in internal battery compartment
|
External |
11 to 28 V DC external power input with over-voltage protection on Port 1 (7-pin Lemo)
|
Power consumption
|
<2.5 W, in RTK mode with internal radio
|
Rover operation times on internal battery |
450/900 MHz systems
|
Receive only, 5.5 hours; varies with temperature
|
Base station operation times on internal battery |
450/900 MHz systems
|
Approximately 4.2 hours; varies with temperature (Tx/Rx)
|
Regulatory approvals
|
- FCC certification Class B Part 15, 22, 24
- Canadian FCC
- CE mark approval
- C-tick approval
- RoHS compliant (excludes those with internal 900 MHz radios)
- WEEE Compliant
|
General
|
Keyboard and display
|
On/Off key for one button start up
|
LED indicators
|
For satellite tracking, radio link reception and power monitoring
|
Receiver type
|
Fully-integrated “Smart” GPS antenna
|
Weight
|
receiver only including internal battery
|
1.35 kg (2.97 lb)
|
complete system (rover including controller and pole)
|
3.7 kg (8.2 lbs)
|
Temperature |
Operating *1*
|
–40 °C to +65 °C (–40 °F to +149 °F) |
Storage |
–40 °C to +75 °C (–40 °F to +167 °F)
|
Humidity
|
100%, condensing
|
Waterproof
|
IPX7 for submersion to depth of 1 m (3.3 ft)
|
Shock and vibration |
Shock – non-operating
|
Designed to survive a 2 m (6.6 ft) pole drop onto concrete
|
Shock – operating
|
To 40 G, 10 msec, sawtooth
|
Vibration
|
MIL-STD-810F, FIG.514.5C-1
|
Measurements
|
- Advanced Trimble Maxwell™ 5 Custom GPS chip
- Trimble R-Track™ technology for tracking the new L2C Civil Signal
- Unfiltered, unsmoothed pseudo-range measurements data for low noise, low multipath error, low time domain correlation and high dynamic response
- Very low noise carrier phase measurements with <1 mm precision in a 1 Hz bandwidth
- L1/L2 signal-to-noise ratios reported in dB-Hz
- 72 channels GPS and GLONASS (option)
- Trimble EVEREST™ multipath signal rejection
- Proven Trimble low elevation tracking technology
- 4-channels SBAS (WAAS/EGNOS/MSAS)
|
Communications:
|
Port 1 (7-pin 0-Shell Lemo) Serial 1
|
3–wire RS232
|
Port 2 (9-pin D-sub) Serial 2
|
Full 9–wire RS232
|
Bluetooth
|
Fully–integrated, fully–sealed 2.4 GHz Bluetooth module
|
Integrated radios
|
Fully-integrated, fully–sealed internal 450MHz Tx or Rx, Tx/Rx *5* Fully-integrated, fully–sealed internal 900MHz Tx or Rx, Tx/Rx *5*
|
450 MHz transmitter radio power output
|
0.5 W
|
900 MHz transmitter radio power output
|
0.5 W (27 dBm)
|
Frequency approvals (900 MHz)
|
USA/Canada (-91) New Zealand/Australia (-92) Australia (-93)
|
Correction data input
|
CMR™, CMR+™, RTCM 2.0–RTCM 2.3, RTCM 3
|
Correction data output |
CMR, CMR+, RTCM 2.0–2.3 |
Data outputs |
NMEA, GSOF. RT17 and BINEX (optional upgrade)
|
*1* Receiver will operate normally to -40°C. Internal batteries are rated to -20°C. *2* Accuracy and reliability may be subject to anomalies such as multipath, obstructions, satellite geometry, and atmospheric conditions. Always follow recommended practices. *3* Depends on SBAS system performance. *4* May be affected by atmospheric conditions, signal multipath, and satellite geometry. Initialization reliability is continuously monitored to ensure highest quality. *5* Tx/Rx with SPS881.
Trimble TSC2 Controller Data Collector
COMBINE FIELD AND OFFICE IN ONE POWERFUL HANDHELD COMPUTER The Trimble® TSC2® Controller is an advanced handheld computer especially designed for Trimble optical and GPS surveying systems. With the Microsoft® Windows Mobile™ 5.0 software operating system, the TSC2 controller runs your choice of powerful Trimble field software. Add specialized applications to the standard Microsoft Outlook Mobile, Excel Mobile, Word Mobile, Power Point Mobile and Internet Explorer programs, and the TSC2 controller becomes a powerhouse of field and office functions on one rugged business device.
SMART, EXPANDABLE HARDWARE Every innovative feature on the TSC2 controller is designed to make your job easier. Clearly view background maps and check work on the vibrant color graphic display for greater data control and confidence. Use the full alphanumeric keyboard, or quickly select software options using the touch screen.The unique TSC2 controller changeable cap enables the use of removable memory or third-party media, such as GPRS, GPS, camera, and product scanner functions. Extend your data logging capabilities and experience a major leap in productivity.
INDUSTRY-LEADING COMMUNICATION TECHNOLOGIES Eliminate cable hassles and expedite setup with integrated Bluetooth® wireless technology. When the TSC2 controller is used with a Trimble R8 or 5800 GPS system, the rover is 100% cable free for unsurpassed convenience and ease of use. The internal 2.4 GHz radio option is ideal for use with a robotic system such as the Trimble S6 total station. Using the expandable media function, a GSM/GPRS modem can add full wireless communication to the Internet in the field.Transfer data in your office over a wireless 802.11 LAN—again, no cables are required. You can also use hotspots to quickly and securely share data with your office from remote locations.
FLEXIBLE COMMUNICATION OPTIONS Choose the method of data transfer that suits your situation. Using an external modem such as a cell phone with Bluetooth, send and receive files over the Internet from the field: you don’t need to drive back to the office. In the office, internal 802.11 technology provides wireless connection to your network. The TSC2 controller also provides USB and serial RS232 communication options; data can be transferred to a PC or another TSC2 controller using a cable, Bluetooth, CompactFlash, or Secure Digital memory card media.
ONE CONTROLLER, ONE SOFTWARE, ONE INTERFACE The TSC2 controller is central to Integrated Surveying™ from Trimble. With an application such as the Trimble Survey Controller™ software onboard, collect and manage both GPS and optical data in one Job file simply by switching the TSC2 controller between sensors. Standardize on one flexible controller for maximized investment. And your survey team only needs to know one interface. When field work is complete, simply transfer the Job file to your office using the communication method that suits your needs.
Features:
- Advanced handheld field computer for exceptional versatility, efficiency, and freedom
- Microsoft Windows Mobile operating system 5.0 software
- Highest flexibility for optical and GPS surveying
- Wireless operations in both the field and office
Specifications:
Physical
|
Size
|
266 mm × 131 mm × 48 mm (10.5 in × 5.2 in × 1.9 in); 76 mm (3.0 in) at handgrip
|
Weight
|
0.95 kg (2.1 lb) including battery; 1.09 kg (2.4 lb) including battery and optional internal radio
|
Memory
|
128 MB SDRAM, 512 MB internal non-volatile storage memory
|
Expandable Memory
|
CompactFlash (CF) card Secure Digital (SD) card
|
Processor
|
520 MHz Intel® PXA 270 XScale CPU
|
Wireless
|
Integrated Wireless LAN 802.11b
|
Power
|
Li-Ion rechargeable pack, 6600 mAh, battery life of 30 hours under normal operating conditions Fast charge to 80% in 2 hours; full charge in 4.5 hours. Battery charge status LED indicator
|
Software
|
The Trimble TSC2 controller runs the Trimble Survey Controller field software. In addition, a number of regional solutions are available. For more information on the field software that’s best for you, contact your local Trimble authorized distribution partner.
|
Environmental
|
Temperature Operating Temperature
|
–30 °C to +60 °C (–22 °F to +140 °F)
|
Storage Temperature
|
–40 °C to +70 °C (–40 °F to +158 °F)
|
Humidity
|
100% condensing, MIL-STD-810F, Method 507.4
|
Sand & Dust
|
Protection against wind-driven according to MIL-STD-810F, and IP6X
|
Water
|
Waterproof IPX7
|
Drops
|
26 drops from 1.22 m (4.0 ft) onto hard surface
|
Vibration
|
MIL-STD-810F, Method 514.5, Procedure I, Fig. 17 & 18
|
Altitude
|
MIL-STD-810F, Method 500.4, Procedures I, II & III, 4572 m (15,000 ft) at +23 °C (+73 °F)
|
Interface
|
Display
|
Color, illuminated TFT, daylight-readable touch screen displayed at 320 × 240 pixels
|
Keyboard
|
53 key alphanumeric keypad, 8-position spider key
|
Audio
|
Integrated speaker and microphone for audio system events, warnings and notifications.
|
Operating system
|
Microsoft Windows Mobile 5.0
|
Input/Output |
Ports
|
RS232 9-pin serial port USB Client USB Host DC Power Port
|
Expansion
|
1 × Type I CompactFlash (CF) slot 1 × Type II CompactFlash (CF) slot 1 × Secure Data (SD) memory card slot
|
|