Trimble SPS 850 Extreme 900Mhz Receiver Installed Options |
Trimble 5700 GPS Receiver Installed Options |
CMR Inputs CMR Outputs RTCM Inputs RTCM Outputs Data Collector Moving Base Bluetooth L2CS UHF Transmit L5 LBand Enable GLONASS Enable Webserver |
CMR Inputs CMR Outputs RTCM Inputs RTCM Outputs Data Collector Binary Outputs Data Logging |
Trimble SPS850 Extreme GPS System Flexible modular receiver for permanent base station, mobile base station and rover operations for GPS modernization.
The Trimble® SPS850 Modular GPS Receiver sets new standards for fast setup and flexible operation in both base station and rover applications. The Trimble SPS850 Receiver supports Global Positioning System (GPS) modernization through support of L2C code, L5 GPS carrier signal, and GLONASS protecting your investment well into the future. The new signals will improve performance in tough satellite coverage environments (deep cuttings, mines, trenches, landfill sites and around tall buildings) and at longer ranges from the base station.
Modularity provides the ability to choose the appropriate GPS antenna for the application, Zephyr Geodetic Model 2 at the base station and the Zephyr Model 2 for the mobile units. The GPS and radio antennas can be mounted high in permanent and semi-permanent base station applications so that they are clear from obstructions and provide maximum radio coverage, while the receiver is locked in a secure environment safe from theft and environmental conditions. The choice of radio antennas allows the customer to either attach it to the receiver itself for mobile base station and rover applications, or use a high gain or directional antenna for maximum range on large job sites.
Standard System Features:
- Integrated GPS receiver and radio
- Internal 450 or 900 MHz radio with Transmit/Receive capability
- 72-channel L1/L2/L2C/L5/GLONASS GPS receiver
- OmniSTAR XP and HP service capable
- WAAS, EGNOS & MSAS Satellite Based Augmentation (SBAS) compatible
- Tough housing
- IP67 environmental rating
- -40 °C to +65 °C (-40 °F to +149 °F) operating temperature range
- 9V to 30V DC input power range with over-voltage protection
- Long life integrated battery. >10 hrs operation as a base station and >12 hrs as a rover with internal Transmit/Receive radio. (New battery operating at room temperature.)
- Integrated display and keypad for system configuration without a controller
- Integrated Bluetooth® for cable free configuration with a controller or Bluetooth enabled radio
- External GPS antenna choice for base station or rover operation
- Rubber duck antenna, or attach a high gain radio antenna for maximum coverage
- Small, lightweight design – 1.65 kg (3.64 lbs) (receiver with internal radio and battery) 4 kg (8.82 lbs) complete system weight (Rover including controller and rod)
- Permanent or semi-permanent base station, or mobile base station versatility
- ATV, belt, rod, supervisor’s vehicle or marine vessel mounting options for rover applications
- Capable of all site measurement and stakeout operations within radio or cellular coverage
- Capable of rover operation within a VRS (Virtual Reference Station) network
- Easy-to-use menu system for fast configuration and status checking
- Autobase for rapid and automated repeated daily base station setups
- Supports IP so that it can be configured and checked remotely over the Internet via an Ethernet port
- One base station receiver can broadcast corrections via multiple radio links. For example, broadcast corrections via an internal 450 MHz radio, as well as an external 900 MHz radio from the same base station receiver
SPS850 Base Station Features:
- Provides unrestricted operational range for rovers and grade control systems
- Base station and rover operation in a single receiver
- Integrated Transmit/Receive radio
- Integrated Ethernet and IP capability facilitates base station and receiver configuration over the Internet or via Ethernet connection on a computer network
- Web-based User Interface allows for remote configuration or troubleshooting
Specifications:
General Characteristics |
Keyboard and display
|
VFD display 16 characters by 2 rows On / Off key for one button startup with Autobase Escape and Enter key for menu navigation 4 arrow keys (up, down, left, right) for option scrolls and data entry
|
Receiver type
|
Modular GPS receiver
|
Antenna type Base Station Rover OmniSTAR Rover
|
Zephyr Geodetic Model 2 Zephyr Model 2 Z+ Antenna
Also supports legacy antennas Zephyr, Zephyr Geodetic, Micro-Centered Choke ring, Rugged micro-centered for GPS L1/L2 operation only
|
Physical characteristics
|
Dimensions (L x W x D)
|
24cm (9.4 in) x 12cm (4.7 in) x 5cm (1.9 in) including connectors
|
Weight
|
1.65 kg (3.64 lb) receiver with internal battery and radio 1.55 kg (3.42 lbs) receiver with internal battery and no radio
|
Temperature Operating Storage
|
-40 °C to +65 °C (-40 °F to +149 °F) -40 °C to +80 °C (-40 °F to +176 °F)
|
Humidity
|
100%, condensing
|
Waterproof
|
IP67 for submersion to depth of 1 m (3.28 ft), dustproof
|
Shock and vibration Shock - non operating Shock – operating Vibration
|
Tested and meets the following environmental standards: Designed to survive a 2m (6.6 ft) pole drop onto concrete MIL-STD-810F, Fig.514.5C-17
To 40 G, 10 msec, saw-tooth MIL-STD-810F, FIG.514.5C
|
Performance characteristics |
Measurements
|
Advanced Trimble Maxwell 5 Custom GPS chip Trimble R-Track ™ technology for tracking the new L2C Civil Signal GLONASS, L5 Signal for GPS modernization High-precision multiple correlator for L1, L2 and L5 pseudo-range measurements Unfiltered, unsmoothed pseudo-range measurements data for low noise, low multi-path error, low time domain correlation and high dynamic response Very low noise L1, L2 and L5 carrier phase measurements with <1mm precision in a 1 Hz bandwidth L1, L2 and L5 Signal-to-Noise ratios reported in dB-Hz Proven Trimble low elevation tracking technology 72 Channels L1 C/A Code, L2C, L5C, L1/L2/L5 GLONASS Full Cycle Carrier WAAS / EGNOS / MSAS
|
Code differential GPS positioning Horizontal accuracy Vertical accuracy WAAS / EGNOS / MSAS2 Horizontal accuracy Vertical accuracy
|
±(0.25m + 1 ppm) RMS, ± (9.84 in + 1 ppm) RMS ±(0.50m + 1 ppm) RMS, ± (19.68 in + 1 ppm) RMS
Typically <1 m (3.28 ft) Typically <5 m (16.40 ft)
|
OmniSTAR Positioning XP Service Accuracy HP Service Accuracy
|
Horizontal 20 cm (7.87 in), Vertical 30 cm (11.80 in) Horizontal 10 cm (3.93 in), Vertical 15 cm (5.90 in)
|
Real Time Kinematic (RTK) positioning Horizontal Vertical Initialization time Regular RTK operation with base station RTK operation with Scalable GPS infrastructure Initialization reliability
|
±(10 mm + 1 ppm) RMS, ± (0.38 in +1 ppm) RMS ±(20 mm + 1 ppm) RMS, ± (0.78 in +1 ppm) RMS Single/Multi-base minimum 10 sec + 0.5 times baseline length in km, <30 km <30 seconds typical anywhere within coverage area Typically >99.9%
|
Electrical characteristics
|
Power Internal External
|
Integrated internal battery 7.4V, 7800 mAh, Li-Ion Internal battery operates as a UPS in the event of power source outage Internal battery will charge from external power source when input voltage is >15V Integrated charging circuitry Power input on Lemo 7 pin 0 shell Lemo is optimized for lead acid batteries with a cut off threshold of 10.5V Power input on the 26 pin DSub connector is optimized for Trimble Li-Ion battery input (PN 49400) with a cut off threshold of 9V Power source (Internal / External) is hot swap capable in the event of power source removal or cut off 9V to 30V DC external power input with over-voltage protection Receiver will automatically power on when connected to external power of 15V or greater
|
Power consumption
|
6.3w, in RTK rover mode with internal receive radio 8.5w, in RTK Base mode with internal transmit radio
|
Rover operation times on internal battery 450 MHz 2.0W systems 900 MHz 1.0W systems
|
12 hrs; varies with temperature 12 hrs; varies with temperature
|
Base station operation times on internal battery External radio 450 MHz 0.5W systems* 900 MHz 1.0W systems
|
16 hrs; varies with temperature 10 hrs; varies with temperature 12 hrs; varies with temperature
|
Certification
|
Class B Part 15, 22, 24 FCC certification Canadian FCC CE mark approval C-tick approval UN ST/SG/AC.10.11/Rev. 3, Amend. 1 (Li-Ion Battery) UN ST/SG/AC. 10/27/Add. 2 (Li-Ion Battery) UN T1 – T8 (Li-Ion Battery) 49 CFR Sections 100-185 (Li-Ion Battery) WEEE
|
Communications Port 1 (7-pin 0S Lemo) Port 2 (DSub 26-pin) Bluetooth
|
3-wire RS-232 CAN Full RS-232 (Via multi-port adapter) 3-wire RS-232 CAN USB (On the Go) (Via multi-port adapter) Ethernet (Via multi-port adapter) Fully integrated, fully sealed 2.4 GHz Bluetooth
|
Integrated radios Channel spacing (450MHz) Frequency approvals (900MHz) 450MHz Transmitter radio power output 900MHz Transmitter radio power output
|
Fully integrated, fully sealed internal 450 MHz, TX, RX or TXRX Fully integrated, fully sealed internal 900 MHz, TX, RX or TXRX 12.5 or 25KHz spacing available Dealer Changeable with TX, TX/RX End user settable with RX only USA (-10), Australia (-20), New Zealand (-30)
0.5w / 2.0w
1.0w (30 dBm)
|
External GSM / GPRS, cell phone support
|
Supported for direct dial and internet based VRS correction streams Cell phone or GSM/GPRS modem inside TSC2 controller
|
Receiver position update rate
|
2 Hz, 5 Hz, 10 Hz and 20Hz positioning
|
Data Input and Output
|
CMR, CMR+, RTCM V2.0, RTCM 2.1, RTCM 2.3, RTCM 3.0
|
Outputs
|
NMEA, GSOF and RT17
|
Carrier
|
Supports BINEX and smoothed carrier
|
Trimble 5700 GPS Receiver
One receiver, many configurations, for
greater flexibility and choice
The Trimble® 5700 GPS receiver is an advanced, but easy-to-use,
surveying instrument that is rugged and versatile enough for any job.
Combine your 5700 with the antenna and radio that best suit your needs,
and then add the Trimble controller and software of your choice for a
total surveying solution. The powerful 5700 GPS system will provide all
the advanced technological power and unparalleled flexibility you need
to increase your efficiency and productivity in any surveying
environment.
Advanced GPS Receiver Technology
The 5700 is a 24-channel dual-frequency RTK GPS receiver featuring the
advanced Trimble MaxwellTM technology for superior tracking of GPS
satellites, increased measuring speed, longer battery life through less
power use, and optimal precision in tough environments. WAAS and EGNOS
capability lets you perform real-time differential surveys to GIS grade
without a base station.
Modular Design For Versatility
For topographic, boundary, or engineering surveying, clip the receiver
to your belt, carry it in a comfortable backpack, or configure it with
all components on a lightweight range pole. With the receiver attached
to your site vehicle, you can survey a surface as fast as you can
drive! For control applications, attach the receiver to a tripod … it’s
designed to work the way your job requires.
Full Metal Jacket & Lightweight
The 5700 GPS receiver boasts the toughest mechanical and waterproofing
specs in the business. Its magnesium alloy case is stronger than
aluminum, but also 30% lighter—the 5700 weighs just 1.4 kg (3 lb) with
batteries. Whether you’re collecting control points on a tripod, or
scrambling down a scree slope collecting real-time kinematic data, the
receiver is light enough and tough enough to carry on performing.
Fast And Efficient Data Storage And
Communications
Use the receiver’s CompactFlash memory to store more than 8,900 hours
of continuous L1/L2 data collection at an average of 15-second
intervals. Transfer data to a PC at speeds of more than 1 megabit per
second through the super-fast USB port. With the option of a UHF radio
modem built in, the 5700 can provide RTK communications without the
need for cables or extra power!
Experience Trimble Integrated Surveying
The Trimble 5700 GPS receiver is designed to support Trimble’s original
Integrated Surveying™ solution. Combine your GPS and optical data in
one job file in powerful Trimble field software such as Trimble Survey
Controller™, then transfer the job file seamlessly to your Trimble
office software, such as Trimble® Business Center, for processing.
Features:
- Proven technology provides dependable performance and precision
- Flexible configurations put you in total control
- Rugged, high-performance hardware is built to last
- Compatible with Trimble Integrated Surveying® technology
Specifications:
Code differential GPS
positioning
|
Horizontal
|
±0.25 m +
1 ppm RMS
|
Vertical
|
±0.50 m +
1 ppm RMS
|
WAAS
differential positioning accuracy
|
typically
<5 m 3DRMS
|
Static
and FastStatic GPS surveying
|
Horizontal
|
±5 mm +
0.5 ppm RMS
|
Vertical
|
±5 mm + 1
ppm RMS
|
Kinematic
surveying
|
Horizontal
|
±10 mm + 1
ppm RMS
|
Vertical
|
±20 mm + 1
ppm RMS
|
Initialization
time |
typically
<10 seconds
|
Initialization
reliability
|
typically
>99.9%
|
Hardware
|
Casing
|
Tough,
lightweight, fully sealed magnesium alloy
|
Dimensions
(W×HxL)
|
13.5 cm ×
8.5 cm x 24 cm
(5.3 in x 3.4 in x 9.5 in)
|
Weight
|
1.5 kg (3
lb) with internal batteries, internal radio,
internal battery charger, standard UHF antenna.
Less than 4 kg (8.8 lb) entire RTK rover including batteries
for 7 hours, range pole, controller and bracket
|
Temperature
Operating
|
–40 °C to +65 °C (–40 °F to +149 °F)
|
Storage
|
–40 °C to
+80 °C (–40 °F to +176 °F)
|
Humidity
|
100%,
condensing
|
Water/dustproof
|
IP67
dustproof, protected from temporary
immersion to depth of 1 m (3.28 ft)
|
Shock and
vibration
|
Tested and
meets the following
environmental standards
|
Shock
|
Non-operating:
Designed to survive a 1 m (3.3 ft) drop onto concrete. Operating: to 40
G, 10 msec, sawtooth
|
Vibration |
MIL-STD-810F,
FIG.514.5C-1 |
|