Trimble SPS780 & SPS750 Basic Base & Rover Set

Quick Overview

Trimble SPS780 Basic & SPS750 Basic Base & Rover Set w/ TSC2 Data Collector & Trimble Zephyr Geodetic Antenna
SKU: GPS83
Item ID: X1488 X1487 X1498 X1489 X1490
Condition: Refurbished
Warranty: 90 Day Exchange

Included

* Trimble SPS780 Basic Rover P/N: 55083-90 w/ Options... [ID- X1487]
         - CMR Inputs
         - CMR Outputs
         - Binary Outputs
         - Bluetooth
         - Lite DC
         - Disable VRS
         - 902-928 MHz Radio P/N: 53620-90
         - Serviced By A Trimble Authorized Service Center
* Trimble SPS750 Basic Base P/N: 58802-90-10 w/ Options... [ID- X1498]
         - CMR Outputs
         - RTCM Outputs
         - Bluetooth
         - UHF Transmit
         - LBand
         - Enable Webserver
         - Firmware Options
         - Serviced By A Trimble Authorized Service Center
* Trimble TSC2 Data Collector w/ Options... [ID- X1488]
         - Bluetooth
         - WLAN
         - Trimble SCS900 Site Controller Software Version 2.33
* Trimble Zephyr Geodetic Antenna [ID- X1489]
* Seco Tripod [ID- X1490]
* QTY. 2 Huber Suhner Cables
* Trimble Dual Clip Cable
* Trimble Battery Charger w/ AC Adapter P/N: 61116-00
* Trimble Multi-Port Power Adapter P/N: 57168
* Trimble Clamp
* Long Antenna w/ Base
* Short Antenna
* Trimble P/N: 49102 Tool
* Battery Pack
* AC Adapter/Charger
* Power Cord
* RS232 PC Interface Cable
* USB PC Interface Cable
* QTY. 2 Hard Carrying Cases

Details

Installed Options
TSC2 Data Collector SPS780 Basic Rover SPS750 Basic Base
- Bluetooth
- WLAN
- Trimble SCS900 Site Controller Software Version 2.33
- CMR Inputs
- CMR Outputs
- Binary Outputs
- Bluetooth
- Lite DC
- Disable VRS
- 902-928 MHz Radio P/N: 53620-90
- Serviced By A Trimble Authorized Service Center
- CMR Outputs
- RTCM Outputs
- Bluetooth
- UHF Transmit
- LBand
- Enable Webserver
- Firmware Options
- Serviced By A Trimble Authorized Service Center

 


 

 

 Trimble SPS780 Basic GPS Receiver
The Trimble® SPS780 Smart GPS Antenna is the simple solution to all your site measurement and stakeout applications. The rugged smart antenna includes an integrated radio, GPS receiver, GPS antenna and battery in a single, lightweight housing designed for maximum portability, quick setup and optimal flexibility.

The SPS780 Smart GPS Antenna offers contractors an easy-to-use, wide area measurement system for a variety of site preparation and grade checking applications. It can be used as either a rover for site measurement and stakeout or as a base station for site measurement and machine control operations. As a base station, the SPS780 takes little or no setup time and only requires a single keystroke each day to start up.

Features:

  • Small, lightweight design – 1.31 kg (2.89 lb) (receiver only with battery) 3.7 kg (8.16 lb) complete system weight (Rover including controller and rod)
  • Quick setup, high mobility base and rover receiver system ideal for small to mid size jobsites and for working on multiple jobsites on a daily or weekly basis.
  • 24-channel L1/L2 GPS receiver
  • Performs all site measurement and stakeout operations within 1.5 km
  • Internal, removable, smart Li Ion battery provides up to 5.5 hrs GPS rover operation per battery. Batteries can be changed when flat, and returned to office or truck for charging leaving the receivers working in the field.
  • Bluetooth® wireless technology for cable free, no hassle base or rover operation
  • Simple keypad with on/off key and LED indicators for power, radio and satellite tracking
  • 2 Hz update rate
  • Allows measurement from a moving platform e.g. mounted on a vehicle, boat or ATV for increased efficiency on large jobsites.


Specifications:

Keyboard and display On / Off key for one button start up
LED indicators For satellite tracking, radio link reception and power monitoring
Receiver type Fully integrated “Smart” GPS antenna
Physical characteristics
Dimensions (WxH) 19 cm (7.5 in) x 10 cm (3.9 in) including connectors
Weight 1.28 kg (2.88 lb) receiver only with internal battery
3.70 kg (8.16 lbs) complete system weight (Rover including controller and pole)
Temperature Operating: –40 °C to +65 °C (–40 °F to +149 °F)
Storage: –40 °C to +75 °C (–40 °F to +167 °F)
Humidity 100%, condensing
Waterproof IPX7 for submersion to depth of 1 m (3.28 ft)
Shock and vibration Tested and meets the following environmental standards:
Shock - non operating: Designed to survive a 2m (6.6 ft) pole drop onto concrete
Shock – operating: To 40 G, 10 msec, sawtooth
Vibration : MIL-STD-810F, FIG.514.5C-1
Performance characteristics
Measurements Advanced Trimble Maxwell™ Custom GPS chip
  • High-precision multiple correlator for L1 and L2 pseudorange measurements
  • Unfiltered, unsmoothed pseudorange measurements data for low noise, low multi-path error, low time domain correlation and high dynamic response
  • Very low noise L1 and L2 carrier phase measurements with <1mm precision in a 1 Hz bandwidth
  • L1 and L2 Signal-to-Noise ratios reported in dB-Hz
  • Proven Trimble low elevation tracking technology
  • 24 Channels L1 C/A Code
  • L1/L2 Full Cycle Carrier
  • WAAS/EGNOS support
Code differential GPS positioning Horizontal accuracy: ±(0.25 m + 1 ppm) RMS
Vertical accuracy: ±(0.5 m + 1 ppm) RMS
WAAS differential positioning accuracy Typically <5m 3D RMS
Real Time Kinematic (RTK) positioning Horizontal: ±(10 mm + 1 ppm) RMS, ±(0.032 ft +1 ppm) RMS
Vertical: ±(20 mm + 1 ppm) RMS, ±(0.065 ft +1 ppm) RMS
Initialization time Regular RTK operation with base station: Single/Multi-base minimum 10 seconds + 0.5 times baseline length in km, up to 30 km
Initialization reliability Typically >99.9%
Electrical characteristics
Power 11 to 28 VDC external power input with over-voltage protection on Port 1 (7-pin Lemo)
Battery Rechargeable, removable 7.4 V, 2.0 Ah Lithium–Ion battery in internal battery compartment
Power consumption <2.5 W, in RTK mode with internal radio
Rover operation times on internal battery 450 MHz systems: Receive only 5.5 hrs; varies with temperature
900 MHz systems: Receive only 5.5 hrs; varies with temperature
Certification Class B Part 15, 22, 24 FCC certification, Canadian FCC, CE mark approval and C-tick approval
Communications characteristics
Communications Port 1 - 3-wire RS-232 (7-pin 0S Lemo)
Port 2 - Full RS-232 (Dsub 9-pin)
Fully integrated, fully sealed 2.4 GHz Bluetooth
Integrated Radios Fully integrated, fully sealed internal 450 MHz, TX, RX or TXRX7
Fully integrated, fully sealed internal 900 MHz, RX only
450MHz Transmitter radio power output: 0.5 w
Receiver position update rate SPS780 Basic: 1 Hz and 2 Hz positioning
Data Input and Output CMR II, CMR+, RTCM 2.1, RTCM 2.3, RTCM 3.0
Outputs 14 NMEA, GSOF and RT17
Carrier Supports BINEX and smoothed carrier



 Trimble SPS750 Modular GPS Receiver

Flexible modular receiver for permanent base station, supervisor's systems and rover operations

The Trimble SPS750 Modular GPS Reeiver sets new standards for rapid stetup and fleible oepratin in both base station and rover applications.

Modularity provides the ability to choose the approipareate global Positiiontiong System (GPS) Antenna for the application, Zephyr Geodetic Model 2 at the base Satation and Zephyr Model 2 for the mobilue Units. The GPS and Radio andtennas can be mounted h igh in permanent and semi-permanenet base station applications so that they are clear from obstructions and provide maximum radio coverage, while the receiver and radio are locked in a secure enviornment safe from theft and the weather. The  choice of radio antennas allows them to be either attached to the receiver itself for mobile base station and rover applications, or equipped with high gain or directional antenna for maximum range on large job site.

Features:

  • Integrated GPS receiver and radio
  • 450 or 900 MHz with Transmit/Receive capability (Max); 450 or 900 MHz radio option with Transmit or Receive (Basic) capability
  • 24-channel L1/L2 GPS receiver
  • OmniSTAR XP and HP service capable
  • WAAS, EGNOS & MSAS Satellite Based Augmentation Systems (SBAS) compatible
  • Tough housing
  • IP67 environmental rating
  • 40 °C to +65 °C (-40 °F to +149 °F) operating temperature range
  • 9V to 30V DC input power range with over-voltage protection
  • Long life integrated battery provides >12 hours operation as a base station with internal Transmit/Receive radio, and >16 hours as a rover.
  • Integrated display and keypad for system configuration without a controller
  • Integrated Bluetooth® for cable-free configuration and operation with a controller
  • Choice of external GPS antenna for base station or rover operation
  • Rubber duck antenna for rover operations, or external radio antenna for a high gain solution in base station operations
  • Small, lightweight design – 1.65 kg (3.64 lbs) (receiver only with battery) 4 kg (8.82 lbs) complete system weight (Rover including controller and rod)
  • Permanent or semi-permanent base station, or mobile base station versatility
  • ATV, belt, rod, supervisor’s vehicle or marine vessel mounting options for rover applications
  • Capable of all site measurement and stakeout operations within 1.5 miles (2.4km) (Basic), >3.0 miles (5km) (Max)
  • Easy to use menu system for rapid configuration and status checking
  • Autobase for rapid and automated repeated daily base station setups
  • Supports IP so it can be configured and checked remotely over the Internet via an Ethernet port
  • One base station receiver can broadcast corrections via multiple radio links. For example, broadcast corrections via an internal 450 MHz radio, as well as an external 900 MHz radio from the same base station receiver (Max)


Specifications;

Keyboard and display VFD display 16 characters by 2 rows
On / Off key for one button start up with Autobase
Escape and Enter key for menu navigation
4 arrow keys (up, down, left, right) for option scrolls and data entry
Receiver type Modular GPS receiver
Antenna type Base Station: Zephyr Geodetic Model 2
Rover: Zephyr Model 2
OmniSTAR Rover: Z+ Antenna
Dimensions (L x W x H) 24cm (9.4 in) x 12cm (4.7 in) x 5cm (1.9 in) including connectors
Weight 1.65 kg (3.64 lbs) receiver with internal battery and radio
1.55 kg (3.42 lbs) receiver with internal battery and no radio
Temperature Operating -40 °C to +65 °C (-40 °F to +149 °F)
Storage -40 °C to +80 °C (-40 °F to +176 °F)
Humidity 100%, condensing
Waterproof IP67 for submersion to depth of 1 m (3.28 ft)
Shock and vibration Shock - non operating: Tested and meets the following environmental standards: Designed to survive a 2m (6.6 ft) pole drop onto concrete MIL-STD-810F, Fig.514.5C-17

Shock – operating: To 40 G, 10 msec, saw-tooth MIL-STD-810F, FIG.514.5C-17
Measurements Advanced Trimble Maxwell 5 Custom GPS chip
High-precision multiple correlator for L1 and L2 pseudo-range measurements
Unfiltered, unsmoothed pseudo-range measurements data for low noise, low multi-path error, low time domain correlation and high dynamic response
Very low noise L1 and L2 carrier phase measurements with <1mm precision in a 1 Hz bandwidth
L1 and L2 Signal-to-Noise ratios reported in dB-Hz Proven Trimble low elevation tracking technology
24 Channels L1 C/A Code
L1/L2 Full Cycle Carrier
WAAS / EGNOS / MSAS
Code differential GPS positioning Horizontal accuracy: ±(0.25 m + 1 ppm) RMS, ± (9.84 in + 1 ppm) RMS
Vertical accuracy: ±(0.50 m + 1 ppm) RMS, ± (19.68 in + 1 ppm) RMS
WAAS / EGNOS / MSAS Horizontal accuracy: Typically <1 m (3.28 ft)
Vertical accuracy: Typically <5 m (16.40 ft)
OmniSTAR Positioning XP Service Accuracy: Horizontal 20 cm (7.87 in), Vertical 30 cm (11.80 in)
HP Service Accuracy: Horizontal 10 cm (3.93 in), Vertical 15 cm (5.90 in)
Real Time Kinematic (RTK) positioning Horizontal: ±(10 mm + 1 ppm) RMS, ± (0.38 in +1 ppm) RMS
Vertical: ±(20 mm + 1 ppm) RMS, ± (0.78 in +1 ppm) RMS
Initialization time Regular RTK operation with base station: Single/Multi-base minimum 10 sec + 0.5 times baseline length in km, <30 km
RTK operation with Scalable GPS infrastructure <30 seconds typical anywhere within coverage area (Max option only)
Initialization reliability Typically >99.9%
Power Internal: Integrated internal battery 7.4V, 7800 mA-hr, Li-Ion Internal battery operates as a UPS in the event of external power source outage Internal battery will charge from external power source when input voltage is >15V Integrated charging circuitry

External: Power input on 7 pin 0 shell Lemo is optimized for lead acid batteries with a cut off threshold of 10.5V Power input on the 26 pin DSub connector is optimized for Trimble Li-Ion battery input (PN 49400) with a cut off threshold of 9V Power source (Internal / External) is hot swap capable in the event of power source removal or cut off. 9V to 30V DC external power input with over-voltage protection Receiver will Auto Power On when connected to external power
Power consumption 6.3w, in RTK rover mode with internal receive radio
8.5w, in RTK Base mode with internal transmit radio
Rover operation times on internal battery 450 MHz 2.0W systems: 16 hrs; varies with temperature
900 MHz 1.0W systems: 16 hrs; varies with temperature
Base station operation times on internal battery External radio: 16 hrs; varies with temperature
450 MHz 0.5W systems: 12 hrs; varies with temperature
900 MHz 1.0W systems: 12 hrs; varies with temperature
Certification Class B Part 15, 22, 24 FCC certification
Canadian FCC
CE mark approval
C-tick approval
UN ST/SG/AC.10.11/Rev. 3, Amend. 1 (Li-Ion Battery)
UN ST/SG/AC. 10/27/Add. 2 (Li-Ion Battery)
UN T1 – T8 (Li-Ion Battery)
49 CFR Sections 100-185 (Li-Ion Battery) WEEE
Communications Port 1 (7-pin 0S Lemo): 3-wire RS-232 CAN
Port 2 (DSub 26-pin): Full RS-232 (Via multi-port adapter)
3 –wire RS-232
USB (On the Go) (Via multi-port adapter)
Bluetooth: Ethernet (Via multi-port adapter) (Max only) Fully integrated, fully sealed 2.4 GHz Bluetooth
Integrated Radios Fully integrated, fully sealed internal 450 MHz, TX, RX or TXRX
Fully integrated, fully sealed internal 900 MHz, TX, RX or TXRX
Channel spacing (450MHz) 12.5 or 25KHz spacing available
Dealer configurable, TX, TX/RX
End User Configurable Rx Only
Frequency approvals (900MHz) USA (-10), Australia (-20), New Zealand (-30)
450MHz Transmitter radio power output 0.5w / 2.0w (2.0w upgrade only available in select countries)
900MHz Transmitter radio power output 1.0w (30 dBm)
Receiver position update rate SPS750 Basic: 1 and 2 Hz positioning
Data Input and Output CMR+, RTCM 2.1, RTCM 2.3, RTCM 3.0
Outputs NMEA, GSOF and RT17 (RT17 Max)
Carrier Supports BINEX and smoothed carrier (Max)
Internal Data Logging Option Provides approx 2 MB of internal memory for static data measurements
450 MHz integrated radio capabilities
SPS750 Basic Base Station Receiver: Transmit only
Rover Receiver: Receive only
900 MHz integrated radio capabilities
SPS750 Basic Base Station Receiver: Transmit only
Rover Receiver: Receive only
SPS750 Basic Base only or Rover only
Measured vector baseline length (Rover operational range from base station)
SPS750 Basic 1.5 miles (2.4 km)
Rover operation within a VRS network using cellular phone dial up
SPS750 Basic Disabled



 Trimble TSC2 Controller Data Collector
COMBINE FIELD AND OFFICE IN ONE POWERFUL HANDHELD COMPUTER
The Trimble® TSC2® Controller is an advanced handheld computer especially designed for Trimble optical and GPS surveying systems.
With the Microsoft® Windows Mobile™ 5.0 software operating system, the TSC2 controller runs your choice of powerful Trimble field software. Add specialized applications to the standard Microsoft Outlook Mobile, Excel Mobile, Word Mobile, Power Point Mobile and Internet Explorer programs, and the TSC2 controller becomes a powerhouse of field and office functions on one rugged business device.

SMART, EXPANDABLE HARDWARE
Every innovative feature on the TSC2 controller is designed to make your job easier. Clearly view background maps and check work on the vibrant color graphic display for greater data control and confidence. Use the full alphanumeric keyboard, or quickly select software options using the touch screen.The unique TSC2 controller changeable cap enables the use of removable memory or third-party media, such as GPRS, GPS, camera, and product scanner functions. Extend your data logging capabilities and experience a major leap in productivity.

INDUSTRY-LEADING COMMUNICATION TECHNOLOGIES
Eliminate cable hassles and expedite setup with integrated Bluetooth® wireless technology. When the TSC2 controller is used with a Trimble R8 or 5800 GPS system, the rover is 100% cable free for unsurpassed convenience and ease of use. The internal 2.4 GHz radio option is ideal for use with a robotic system such as the Trimble S6 total station.
Using the expandable media function, a GSM/GPRS modem can add full wireless communication to the Internet in the field.Transfer data in your office over a wireless 802.11 LAN—again, no cables are required. You can also use hotspots to quickly and securely share data with your office from remote locations.

FLEXIBLE COMMUNICATION OPTIONS
Choose the method of data transfer that suits your situation. Using an external modem such as a cell phone with Bluetooth, send and receive files over the Internet from the field: you don’t need to drive back to the office. In the office, internal 802.11 technology provides wireless connection to your network. The TSC2 controller also provides USB and serial RS232 communication options; data can be transferred to a PC or another TSC2 controller using a cable, Bluetooth, CompactFlash, or Secure Digital memory card media.

ONE CONTROLLER, ONE SOFTWARE, ONE INTERFACE
The TSC2 controller is central to Integrated Surveying™ from Trimble. With an application such as the Trimble Survey Controller™ software onboard, collect and manage both GPS and optical data in one Job file simply by switching the TSC2 controller between sensors. Standardize on one flexible controller for maximized investment. And your survey team only needs to know one interface. When field work is complete, simply transfer the Job file to your office using the communication method that suits your needs.


Features:

  • Advanced handheld field computer for exceptional versatility, efficiency, and freedom
  • Microsoft Windows Mobile operating system 5.0 software
  • Highest flexibility for optical and GPS surveying
  • Wireless operations in both the field and office

Specifications:
Physical
Size
266 mm × 131 mm × 48 mm (10.5 in × 5.2 in × 1.9 in);
 76 mm (3.0 in) at handgrip
Weight
0.95 kg (2.1 lb) including battery;
 1.09 kg (2.4 lb) including battery and
 optional internal radio
Memory
128 MB SDRAM, 512 MB internal non-volatile storage memory
Expandable Memory
CompactFlash (CF) card
 Secure Digital (SD) card
Processor
520 MHz Intel® PXA 270 XScale CPU
Wireless
Integrated Wireless LAN 802.11b
Power
Li-Ion rechargeable pack, 6600 mAh, battery life
 of 30 hours under normal operating conditions
 Fast charge to 80% in 2 hours; full charge in 4.5 hours.
 Battery charge status LED indicator
Software
The Trimble TSC2 controller runs the
 Trimble Survey Controller field software. In addition, a number of
 regional solutions are available. For more information on the field
 software that’s best for you, contact your local
 Trimble authorized distribution partner.
Environmental
Temperature
Operating Temperature

–30 °C to +60 °C (–22 °F to +140 °F)
Storage Temperature
–40 °C to +70 °C (–40 °F to +158 °F)
Humidity
100% condensing, MIL-STD-810F, Method 507.4
Sand & Dust
Protection against wind-driven according
 to MIL-STD-810F, and IP6X
Water
Waterproof IPX7
Drops
26 drops from 1.22 m (4.0 ft) onto hard surface
Vibration
MIL-STD-810F, Method 514.5, Procedure I, Fig. 17 & 18
Altitude
MIL-STD-810F, Method 500.4, Procedures I, II & III,
 4572 m (15,000 ft) at +23 °C (+73 °F)
Interface
Display
Color, illuminated TFT, daylight-readable touch screen
 displayed at 320 × 240 pixels
Keyboard
53 key alphanumeric keypad, 8-position spider key
Audio
Integrated speaker and microphone for audio system events, warnings and notifications.
Operating system
Microsoft Windows Mobile 5.0
Input/Output
Ports
RS232 9-pin serial port
 USB Client
 USB Host
 DC Power Port
Expansion
1 × Type I CompactFlash (CF) slot
 1 × Type II CompactFlash (CF) slot
 1 × Secure Data (SD) memory card slot

 

 

Trimble Zephyr Geodetic Antenna

The Trimble Zephyr Geodetic antenna is ideal for control work. The Zephyr Geodetic incorporates a large Trimble Stealth™ Ground Plane, which literally burns up multipath energy using technology similar to that used by Stealth aircraft to hide from radar. It is protected by weather-resistant materials and a low profile design, so when the antenna is used for a permanent installation, you can count on many years of continuous operation without the need for a radome.